This DIY nautical side table is easier to make than it looks!
I was
halfway between Toronto and home - a 1600km journey - when I agreed to participate in the
#LoveYourWood contest, sponsored by
Rust-Oleum and
Varathane. Sure, I was super exhausted. And yes, we had a
stalled bathroom reno to complete. But the folks at Rust-Oleum have been
so good
to me: helping me
give our bathrooms a facelift and tackle
a million other projects, so of course I was on board! I didn't even realize when I said yes that this was
a contest with prize money on the line... I just like making things.
Here's the challenge: myself and 7 other bloggers were each mailed a mystery box of Varathane products, some truly random bits and bobs, and a small budget to makeover or build something cool:
Almost immediately I chose the wire, rope, and sack of marbles, simply because I like a challenge (marbles?!?). In fact, I went out and bought 100 more feet of rope so I could create a bold, nautical side table. Go big or go home right? I also stepped outside my comfort zone and refrained from adding my signature aqua, but I had no trouble dreaming up a surplus of ideas - which is always my problem.
Supplies for Making a Square Wood Table:
- Three 1.5" x 1.5" pine lumber pieces (8 foot lengths)
- Two 3/4" x 1.5" pine lumber pieces (6 foot lengths)
- One 3/4" x 3/4" pine lumber piece (6 foot length)
- Scrap piece of pine 3/8" plywood
- Piece of wallpaper (click for similar)
- 50-75 feet of rope
- Wire
- Handful of round blue marbles
- Epoxy to secure marbles
- Wood glue
- Air nailer and 3/4" air nails (14 gauge)
- Circular saw and mitre saw
- Brushes, rags, gloves etc. for stain application
- Varathane Ultimate Wood Stain - Chocolate
- Varathane Professional Clear Finish - Satin
- Varathane Bar and Table Finish
Why use pine?? I didn't particularly want pine, but I didn't want to have to rip larger boards. I wanted to purchases the exact dimensions and just cut the lengths. The sizes I wanted were available in a few different kinds of wood, but if I wanted them all the same, pine was my only option. Because everything was pine, it took the stain more evenly than if I had mixed woods.
How to Make a Square Wood Table:
After some pondering and scheming, we started with one of our wonky little sketches:
Once we had a sketch of the design and figured out our desired measurements, we cut all of the pieces to length using a mitre saw. The frame for the top and bottom were cut with mitred corners, while the vertical pieces that make up the legs were just butt jointed. We also cut the smaller square "frame" for the top, to create a channel for the marbles. Finally, to make the table surface, we cut a scrap of plywood to size (leftover from
the Ikea credenza hack!) using our circular saw with a straight edge - which we use as a table saw stand-in.
With the cutting done, we formed the square base and top by butt gluing the ends together with wood glue, securing them while they dried. We also glued together the small inner frame. Once those pieces were dry, we glued the plywood into the frame, securing it on the bottom as well. Finally, we glued the four legs onto the top and bottom, completing the cube shape.
Here's a peek at the table before stain (the inner frame hasn't been attached yet):
Pretty, right? It took
so little time that now I have this weird compulsion to make a bunch of these cube cuties. Anyone need a table?
To drill the holes for the rope, first we plotted out the spacing - enter another wonky drawing:
Then we worked our way around the table, laying the table on its side, with a piece of scrap wood underneath. All of the holes are drilled in equal distance, except for the first and last (for the rope to double back and be tied). We used a 1/2" drill bit for our rope.
Next we figured out where the marbles would be placed. Inspired by the rivets on this
nautical mirror available on 1st dibs, I spaced the marbles around the perimeter of the table top, holding them down with tape while I fiddled with the arrangement until I was happy.
To create dents for the marbles to sit in, we measured, marked, and simply drilled a partial hole with a 1/4" drill bit (you could also use a counter sink bit, which we don't have).
With the table assembled and the holes drilled, we lightly sanded the entire piece with 220 grit sandpaper - paying attention to where the holes had been drilled on the legs. We sand after construction because sharper cuts make for cleaner construction. Once it's assembled, we sand rough areas smooth and also round corners a tiny bit, which makes it look good but also makes it less susceptible to chips and dings - sharper edges are more vulnerable.
Once it was sanded smooth, we wiped it with a tack cloth to remove any dust and debris, and then it was time for stain! In my mystery package, I received Varathane Ultimate Wood Stain in Chocolate and Varathane Professional Clear Finish:
The stain went on very easily and smoothly and, as promised, only took
one coat! It did, however, take longer to dry than indicated, which
could be attributed to humidity in the air. I ran out of daylight and
ended up letting it dry overnight before applying the clear coat with a
brush. The nice thing about an oil-based stain as opposed to
the water-based stains I've used before is that this didn't raise the grain - which makes for much less work!
Next I cut a piece of wallpaper I've been
swooning over - the Whitby pattern by Mini Moderns,
available from Wallpaper Direct.
I
really wanted
the aqua but ordered the
washed denim blue because I knew it would look better with the blue marbles (it was so weird to be running around town with a sack of marbles, trying to find complementary elements for my table!). You can't even imagine how long I
agonized over this decision and how much it
pained me to order the denim blue. As lovely as it is, turning down aqua took a lot of willpower.
I think I
earned a vote just for that ;)
We used double sided tape to affix the paper to the plywood top (not the best idea - I'll tell you why), and then installed the inner frame on top of it, using wood glue and air nailing it from the bottom.
We used
our go-to fixative to affix
the marbles, adding a dab of epoxy to each marble and pressing it down gently.
The marbles held tight and definitely could have been left, as-is.
Then it was time for the scary bit: resin!! I've been itching to try using resin on furniture (after
pinning a bunch of cool projects) and thought this contest would be a great reason to experiment. With cash on the line, why not try using a product you've never used? Better still, try it at 10pm, the night before the project is due...
I would have fared well on Trading Spaces - I clearly live dangerously and can pull a DIY all-nighter without breaking a sweat.
Using the Varathane Bar and Table Varnish:
We followed the instructions - mostly - and although there are warning signs on every page of the instruction pamphlet, it was actually easy to use! We applied it to the channel we created for the marbles and also over the wallpaper. Now, the instructions suggest laminating papers to be embedded, but it was too late for that so I went ahead! I only got the product a couple of days before, and if I hadn't been on a deadline I would have done that extra step - or, as per my genius last minute revelation: done a glass top for the surface and then epoxy for just the marble channel! The wallpaper was changed a bit from the moisture of the epoxy and lost some crispness. But, even though we deviated from the instructions and poured it on very thickly, it cured and dried in time. I just love how glossy it is and how it reflects light. So, playing fast and lose with instructions, you win some and you lose some.
Finally, we created
a bowline knot and threaded the rope back and forth through the holes we drilled, securing the
bitter end (I'm studying for my boater's exam) with the wire. And,
that's it!!
My nautical table using rope, marbles, and wire - plus chocolate stain, a satin clean coat, and epoxy:
I love how this DIY nautical table turned out!
Thanks to Rust-Oleum and Varathane for sponsoring such a fun challenge. And special thanks to Wallpaper Direct for providing the wallpaper. I have more plans for my leftover paper - which is so dreamy (and I keep thinking about wallpapering my powder room in the aqua. The AQUA!)
