How to Update Pot Lights without Replacing the Can

We recently updated our kitchen pot lights with a quick fix:



Our kitchen has two pot lights over the counter that I usually croped out of photos because they just looked so terrible!  In the lakehouse tour, you can see them in the "before" photos, but they're cropped out of every "after" shot of our aqua makeover.  They functioned well and I used them every day, but they were old and discolored, and one of them had just been coated in silicone by the silicone-happy former owner:

I'm seriously embarrassed that we lived with them for so long!

We had been wanting to replace them for awhile, but we weren't enthusiastic about climbing into the attic to remove the cans.  Recently one of the bulbs burned out so we headed to The Home Depot for a new one.  They're $10!  I suggested to Handy Hubby that we finally replace the lights and purchase two fresh bulbs - I didn't want to end up with two different bulbs in addition to wonky lights.  We sauntered over to the lighting section and pondered for awhile.  Finally, we made our selection and were about to head to the check out when a salesperson asked if we needed help.  We asked how difficult it would be to replace our pot lights, and if he had any tips.  He discouraged us from replacing them because removing the cans could really damage a ceiling.  Instead, he showed us the LED bulb and trim retrofit kits.  They're actually a bit more money than purchasing new cans, but it is so much easier to use these kits to update the look and technology.



Here's how we updated our pot lights, the easy way.  First we bought two Halo LED 4" retrofit kits from The Home Depot, for about $50 a piece.  This one is fairly similar.

As with any electrical work, we turned off the power.  Then we removed the old pot light trim by gently pulling it down and then squeezing the metal retaining wires that held it in place.

The arrow is pointing to the wires:

Then we were left with just the can, which was perfectly functioning and really not that old:

Then it was time to install the new light and trim retro fit kit!

First we installed the light socket adapter.  Then we took the new LED and plugged it into the adapter.  With a screw driver, we used one of the self-tapping screws (included) and screwed the ground wire into an existing hole in the can.  Instructions are included with the kit, and we followed them completely.

The installation was straightforward, except we hit ONE stumbling block: when we tried to push the trim in tightly against the ceiling, the can shifted too so we couldn't get a nice, flush fit.  Genius Hubby (I call him "Handy Hubby" for a reason), figured out that if he threaded a wire through the gap between the gimbal and the trim, looped it around a fixed point in the can, and then back through the trim, he could pull down on the wire to hold the can down while pushing the new trim piece up.  It worked!  Once it was tightly in place, he pushed the wire back through and removed it.  You might not need this step, but it's a handy hack to know, just in case.

The light bulbs should last 50,000 hours and only draw 10 watts, but they are SO much brighter than our old lights, which were 50 watt halogens.  Now that the days are getting shorter, I love that I have brighter kitchen lighting, although I do miss the halogen bulbs a tiny bit.  They were dimmer, but a touch warmer.  These are bright and offer a very white light - much better than flouescent, but I'm still clinging to my incandescent bulbs and irrationally resistant to liking any other type of bulb. 

It goes without saying, though, that they just look so much better now!

Now we're eyeing up the eyeball pot lights above the fireplace and thinking that we might use this same style of LED retro fit to update those, too...

Salamander? Check. Also: How to Stop Gutters from Leaking

Hubby and I tend to drag our heels a bit when it comes to projects around the house that lack a certain panache.  But we are motivated by saving money, so when our municipality offered a free landfill day, well, that lit a fire under our bums to get some things done (normally a truckload is $25).  It started with cleaning out the garage and tidying up around the property so we could take the opportunity to throw out/recycle all of the debris, but once we were in the zone there was no stopping us.  We replaced/added about half a dozen motion lights (now a squirrel can't even cross our property without being lit up like an opera singer), and put up driveway markers in the hopes that this winter I won't ditch the truck (again).  We gleefully stashed the lawnmower, but sadly serviced the snowblower, plus I got a refresher course in operating it (I do 50% of the snow removal, yay).  We were busy bees!  Shortly before free dump day we realized that we had a bit of room left in the truck, so we decided to remove the busted stairs leading up to the garage.  Hubby had acccidentally put his foot through a rotten step in the summer - it was in terrible shape and totally pointless. 

He tackled Project Stair Removal while I was giving our headboard a refresh.  We allotted ourselves a half hour to complete our respective tasks.  While it took me closer to an hour to spray paint the headboard and nightstands, Hubby realized he could just flip up and remove the entire set of stairs in minutes, instead of taking it apart piece by piece as he had planned.

He spent the rest of his half hour examining the salamander he found:

Once the salamander was thoroughly examined, we tackled a few more projects - propelled by the victorious feeling that accompanies a problem-free project.  Our gutters had been leaking all summer, so I asked my friends at Rustoleum if I could try some Leak Seal:

I tried to demonstrate the leaking in a manner that didn't involve me standing outside in the pouring rain (I think Hubby longs for the pre-blog DIY days when we didn't have to document everything):  

Happily, the Leak Seal - a flexible rubber sealant - seemed to work perfectly and it took barely any time at all to seal up the cracks.  Eagle-eyed Hubby had been keeping tabs on the gutters during rainy days and already knew exactly which spots needed sealing.  Next spring we want to add gutter guards because they get filled with leaves and cleaning the gutters is a weekly job, but at least they're no longer holey.

We were on fire, right?  I even started doubling up on jobs.

While we were splitting and stacking firewood at my father-in-law's, I absconded into his awesome spray painting booth and knocked out a few fun projects (photos soon!).  I also tackled one boring one: our doorbell cover was beige and stood out against our white walls.  A blast of Rust-Oleum's Universal Paint + Primer solved that problem!  I obviously love that this paint is formulated for plastic. 

I really wish I had painted to doorbell cover in the townhouse.  It always bothered me but I just never got around to it, not because I didn't have the time, but because it seemed like a totally boring project and so I avoided it.  It truly was a boring project, and I doubt you even spotted the difference in my most recent hallway post compared to the original reveal, but every day I notice the difference.  I'm so happy I took the five minutes to paint it.

Now

Before

Our to-list is far from complete, and now that we've discovered that all 202 episodes of The X Files are on Netflix I suspect our productivity will decline, but I'm thrilled that we tackled so many projects this fall that normally get eclipsed by more fun and rewarding projects, like making frames for paintings and rub 'n buffing hardware. 

A huge thanks to Rust-Oleum for providing the Leak Seal and Universal Paint + Primer (and thereby also providing that extra dose of motivation to get stuff done!)

Read more »

Getting a New Propane Furnace - What to Expect

When Hubs and I first viewed the lakehouse, we were a little concerned about the electric forced air.  "Isn't that going to be pricey?" we murmured, mesmerized by the view and barely able to think straight.  Our realtor asked the homeowner for past electric bills which, despite being "pretty low," never materialized.  We weren't really that concerned, because we decided that if it proved too pricey, we were willing to convert to propane heat.  Our realtor, home inspector, and family friends who had made the switch to propane heat all guessed around $2000.  Two thousand?  Crikey.  But it seemed manageable and so the sale moved forward.

By the time we moved into the lakehouse, it was the belly of winter and so we hunkered down and tried to keep warm.  $800 monthly electric bills chilled us to the bone more than the blizzards - we almost broke $900.  The worst part was that it wasn't even that warm, despite those crazy heating costs.  Some days we could only get the house up to sixteen degrees Celsius (60 Fahrenheit).  We supplemented a little with our wood burning fireplace but all of our wood was buried...somewhere on the property (we couldn't remember where because when we finally moved in everything was blanketed in huge snow drifts)...and so we rationed the wood supply.  For some reason, just ordering more wood didn't cross our minds.  I guess our brains were numbed from the cold.  I took to wearing boots indoors and forced Szuka to cuddle me.

Gratuitous winter photo, shared on Instagram only 6 months ago!!

By spring, we had decided definitively that our furnace needed to go, not only to save on our heating bills, but also to actually heat the house!  We started calling around for estimates and, to our chagrin, were quoted $5000-7000!!  Yep.  Many more thousands than we thought - and had saved up for.  Luckily, the older gentleman who had installed Hubby's Dad's system was not retiring as we had all thought and so he also came by to give us a quote.  His estimate was much lower - only (only!) $4900, including taxes and after rebates.  And so we set about spending $5000 on the least fun thing ever.  Ta da:

Our new furnace is a Coleman, 80,000 BTU.  It's a modulating gas furnace, with variable speed blower, which means that it varies the heat output with fewer starts and stops and is more efficient than a furnace that just cycles on and off.  We were originally quoted a furnace with 70,000 BTU but ended up forking over the extra $100 for this larger one, just in case.  It gets really windy lakeside, and that gorgeous wall of windows in the living room definitely lets a lot of heat escape (even if they are double pain argon filled).  A lot of our hot air also gets trapped in the 13 foot tall peak of the living room ceiling, but the ceiling fan helps push some of that air down.  Suffice to say, although it's solidly built, well insulated and fairly new, this house was not built with heat retention in mind - it was someone's summer home, after all. 

The installation process was swift and seamless.  The clunky old furnace was removed and the new one installed in its place - it's half the size - in one day, with a few adjustments made the next day.  While the furnace installer completed the installation, the propane service arrived with our shiny new tank.  It's an eyesore, to be sure, but there were many, many regulations as to where it could go and in the end, this was the only spot - nice and visible from the driveway.  At least it doesn't hamper the view!  When we originally called the propane company to get the details, set up an appointment, create an account, etc., we were told they'd dig the trench from the tank to the house (for a fee, of course) but during the house call we were informed that they only dig a trench if they might lose a customer.  Long story short, Hubs dug a 25 foot, 16" deep trench and also leveled the area where the tank was to be placed.  



Once the tank was set in place, the line was laid in and connected to our house (where an unsightly main gas valve mounted on the gas regulator now resides - I guess I'll be planting some shrubs next year).



Hubby filled in the trench and flipped back the sod.  Thanks to gusting winds and falling leaves, you can't even see where the trench was dug. 

This new system comes with some responsibilities.  As a reader astutely pointed out, we'll need a propane detector.  In the event of a fire (please, universe, no), we should try to turn off the propane via an exterior valve.  We also need to monitor our propane levels and at 30% arrange a delivery.  We'll likely have to fill the tank twice annually and if it needs a refill in the winter, we need to clear a path through the snow (goody). 

Happily, though, we have heat.  The lakehouse is toasty, which I hope will also be true in the dead of winter.  With our new system, we also added a Nest thermostat, which so far we're very pleased with.  It seems very responsive and we love that we can leave the house cool while we're gone and before we head home, turn up the heat from our cell phones so we arrive to a warm home, which we didn't waste money heating in our absence.  I'd like to test the Nest thermostat a little more and then provide a more thorough review of it and our three Next smoke detectors.

Will the propane save us money?  Only time will tell definitively, but from our calculations we should.  As I mentioned, our electricity bills throughout the winter were $800 but the non-heating portion of that was about $200, so our heating costs were really more like $600.  Now our worst monthly heating bills should ring in at around $300 per month.  It will take awhile to recoup the cost of our new furnace but, given that our old one was either failing or not the appropriate size/capacity, it just made sense to switch now. 

I have to admit that although Hubs and I didn't enjoy writing two colossal cheques to the furnace installer and propane delivery service, we're not even as bummed about it as we thought we'd be.  Yes, I can think of a million things I'd have rather spent the money on (another European vacation, our upcoming bathroom reno, a new washer and dryer in aqua, beefy truck bumpers, all the pyrex in the world) - and it would have been nice to negotiate a better price when we bought the house given this expense, but I forgot how lovely it is to have a warm house.  It's fabulous!  I wouldn't trade it for anything.  We absolutely love our lakeside life and plan to be in this house for a good long time.  Making this investment in our home feels good, and feeling warm feels even better. 

Some Things We Learned in the Process:

• Don't rely on hearsay quotes! I wish we'd called around for quotes around the time we bought the lakehouse - not only to possibly negotiate a better price, but also just so we would have had a more realistic number in mind and could have saved up more money for this monster purchase.
• Don't wait until it's cold! We had to go a day without a furnace during the conversion and with our wood-burning fireplace we were okay but overnight we were a bit chilly.  It would have been better to do this in the spring or summer.
• Find out what your responsibility is.  It turned out we needed to coordinate everything and be a middle man between the furnace installer, energy company, and the propane delivery, on top of our trench-digging and ground leveling duties.
• Find out ahead of time where the tank can/should go so you have time to prepare the area.  It only took a couple of days, but knowing ahead of time let us schedule the digging on non-rainy days.
• Contact the electric/energy company for a line locate.  Ours came out and marked the lines so we knew where not to dig.  As a bonus, they even marked the lines from the house to the garage which isn't even their responsibility, so we were really appreciative that they located those too.
• Look into available rebates and ask your furnace installer if he/she knows of any additional offers.
• Ask about referral bonuses.  Our propane company gave a bonus to us and my father-in-law because he "referred" us to their service.  A little cash back never hurts (we were going to go with this propane company anyway - shhh, don't tell them).
• Be wary of companies unwilling to do a site visit.  The company selling you a furnace and install should see your home, current furnace, chat about your needs/etc., before providing a quote.  One company refused to meet us or see the home, and we immediately removed them from our list.  They were also the highest quote, so they may have also been intending to sell us more furnace than we needed. 
• Ask for an itemized estimate so you can see the breakdown of materials/labor/etc.
• Find out the specifics of the equipment - the furnace, the thermostat, etc. - because you might want to make substitutions.  Our furnace installer doesn't use Nest products but we really wanted to try that thermostat so we purchased and installed it ourselves.  We also chose a larger furnace than he recommended, just to be safe, but we discussed all of these decisions with him because he's the expert.  Here's a good guide to calculating BTU's required.

Hopefully this will be even the teensiest bit helpful to anyone converting from electric to propane forced air, or just shopping for a new furnace.  At the very least, if you've got a really big, really boring purchase to make (or you just made one), know that you're not alone!   

Read more »